BASIC SERIAL COMMAND SPECIFICATIONS 103-010100-01(LX-380) 103-009100-01(LX-450) Ver. 1.00 Ver. Rev.A Page 1
6.4. Operation Requirements When the projector’s status in this below, Functional Execution Commands are limited. Projector Status Available Function
6.5. POWER ON Command Command “C00” [CR] Detail Power ON When already Power is ON, nothing is done. When sending this command during Countdown in pro
Ver. Rev.A Page 12 Unacceptable “?”[CR] 6.10. INPUT 3 Command Command “C07” [CR] Detail Select INPUT 3. This command operates differently from “In
6.15. SOUND MUTE OFF Command Command “C0C” [CR] Detail Sound Mute OFF. This command works the same way as “MUTE” button of the remote control for Mu
Ver. Rev.A Page 14 Unacceptable “?”[CR] 6.21. MENU OFF Command Command “C1D” [CR] Detail Clear Menu of On Screen Display. Acceptable [ACK] [CR] R
6.27. INPUT 2 RGB Command Command “C25”[CR] Detail Select RGB input in Input 2. Acceptable [ACK] [CR] Response Unacceptable “?”[CR] 6.28. IMAGE
Ver. Rev.A Page 16 Detail Set Power Management OFF. This status is stored in EEPROM and retained regardless of Power ON/OFF. Acceptable [ACK] [CR]
Ver. Rev.A Page 17 Acceptable [ACK] [CR] Response Unacceptable “?”[CR] 6.39. POINTER RIGHT Command Command “C3A” [CR] Detail Move the Pointer o
6.44. FREEZE ON Command Command “C43” [CR] Detail Freeze on-screen image. This command works the same way as “FREEZE” button of the remote control fo
6.50. INPUT 1 Analog RGB Command Command “C50” [CR] Detail Select Analog RGB input in Input 1. Acceptable [ACK] [CR] Response Unacceptable “?”[CR]
- CONTENTS - 1. Overview... 4
6.56. LENS SHIFT LEFT Command Command “C5F” [CR] Detail Move projection area to the left. Acceptable [ACK] [CR] Response Unacceptable “?”[CR]
Ver. Rev.A Page 21 Detail Correct keystone distortion by reducing down part of image. This command executes both keystone distortion correction and
7. Status Read Command 7.1. Format 7.1.1. PC issues commands in format as below; “CR” Command [CR] Command:1 character(See Basic Status Read Command
7.3. Status Read Command Command “CR0” [CR] Detail Get the projector’s operating status Acceptable “%1” [CR] %1 ”00” = Power ON “80” = Standby “40”
7.3.5. “10” [CR] Status: Power Failure When the power supply voltage inside the projector reaches abnormal status, the projector is automatically turn
7.3.11. “81”[CR] Status: Standby after Cooling down due to lamp failure The projector has recovered from Lamp Failure status. When the projector enter
7.7. Temp Read Command Command “CR6” [CR] Detail Get the temperature data inside the projector. With some temperature sensors installed in the projec
6.28. IMAGE Command ... 15 6.29. ON START Setting Comman
7.6. Setting Read Command ... 25 7.7. Temp Read Command...
3. Notes for Communication 3.1. The projector control command is defined as one command/one line that starts with “C” and ends with carriage ret
for INPUT switching command. 3.12. The number of characters of response to Status Read Commands depends on commands. Please see [7. Status Read Com
Command Item Command Item C40 ――― C80 ――― C41 ――― C81 ――― C42 ――― C82 ――― C43 FREEZE ON C83 ――― C44 FREEZE OFF C84 ――― C45 ――― C85 ――― C46 Z
5. Status Read Command Table Command Item Memo CR0 Status Read CR1 Input Mode Read CR2 ――― CR3 (Corresponding) Lamp Time Read CR4 Setting Rea
6. Functional Execution Command 6.1. Format 6.5.1. PC issues a command in format as below. “C” COMMAND [CR] Command: two characters (See Basic Functi
Kommentare zu diesen Handbüchern